You were looking for it and you found it! A while ago, setting up IPTV Mag 250 was never easy. But today, with just one click, you can do it freely.
In this article, we will define Mag 250 and introduce some basic concepts about it. In other words, we will show you some steps to follow to successfully configure this IPTV.
What is a 250 mag?
The Infomir MAG 250 micro console is an Infomir development that combines the maximum technical possibilities. It meets all the broadband requirements set by the supplier....
Steps to configure iptv MAG 250
To configure this micro console, it is necessary to follow certain steps. These steps are:
Step 1
We put the downloaded firmware, the mcast.exe program and the DHCP server in a folder at the root of the C:\ drive. Please note that there must be 2 files in the folder to flash the TV Box: Bootstrap and imageupdate. Therefore, the downloaded Bootstrap_250 file will simply have to be renamed to Bootstrap.
Step 2
On the network card through which we will connect the decoder , you need to register the IP address 192.168.1.1 and the mask 255.255.255.0. To do this, press the key combination Win + R and in the open time, write the command ncpa.cpl.
Next, click the OK button. In the Windows Network Connections window that opens, select the desired network connection and right-click on it. In the context menu, select Properties. Then select the Internet Protocol Version 4 (TCP / IPv4) component. We click on it twice and enter the IP address:
Step 3
Connect the LAN port of the MAG-250 TV box and the network card of the computer with a cable .
Step 4
Activate the MAG-250 prefix and immediately press the Menu button several times. The TV box BIOS should open. Thus, in some cases, the software will not be downloaded until you reset the device configuration using the "Def.Settings" item.
After that, make sure you go through the "Exit & Save" item, otherwise nothing will be reset.
Step 5
Start the DHCP server on the computer . In the case of the DualServer I suggested, you need to start the Windows command line. To do this, press the Win + X key combination and in the menu that opens, select "Command Line (Administrator)". There we write the command: Press Enter to start the server.
Step 6
Run the mcast.exe program to broadcast the bootloader and firmware. Upon startup, it will ask you to select the desired network interface. To do this, select IP: 192.168.1.1, Local Area Connection and press the Select button. The main program window will open: Here, you will need to correct the address in the first stream (Stream 1).
The MAG-250's broadcast address should be: 224.50.0.70:9000. The second stream address should be: 224.50.0.51:9001. Click the Start buttons on both threads. The bootloader and firmware will be multicast.
Step 7
In the BIOS of the set-top box, select the "Upgrade Tools" item. Then you need to select the "MC Upgrade" item. The STB will start catching the bootloader. After loading Bootdtrap, the prefix will write: Boot message: Receiving an image is started! This means that your STB box has started downloading the firmware.
This caption should change to "Boot message: Writing image to flash memory." Once the set-top box has written the firmware to memory, it should display a message. This message is: Image writing to flash memory successful! After that, the set-top box should reboot and your MAG-250 or IPTV RT-STB-HD should boot with the new firmware.
Some steps to follow to Flash MAG-250 and IPTV RT-STB-HD from the internal portal.
Step 1
Select the Settings section in the menu: We arrive at the settings menu of the MAG-250 or RT-STB-HD decoder. To enter the service menu, press the Set or Setup button. In front of us is the service menu of the TV decoder.
Step 2
Select the Update Software menu item.
Step 3
Using the arrows, select the “Update via USB” type. Click the Start Update button.
Step 4
Press the "Verify" button to check the firmware on the USB flash drive. If the firmware check is successful, the "Start" button will become available. We press it and wait for your TV box to be sewn. Option 2.
Step 5
Restart the console and hold the Menu button while loading to enter the MAG-250 BIOS.
Step 6
In the MAG-250 or RT-STB-HD BIOS, select the "Upgrade Tools" section: then - "USB Bootstrap". If the flash drive is not connected to the MAG-250, the prefix will write it. You must connect the USB flash drive to the console and press the OK button.
After that, the decoder will check for the presence of firmware on the removable media. If everything is OK, it will start the flashing process from a USB flash drive from a USB flash drive. At the end of flashing the MAG-250 TV decoder, the message "Writing the image to be flashed successfully" will appear.
Conclusion
Overall, STB MAG 250 prefixes are very popular worldwide. These devices have been used by many providers to organize digital television. The beauty of these receivers is that they can be flashed with alternative DNA firmware.
In addition, they can use the full potential of the device. This allows you to watch channels without restrictions, and regularly enjoy the benefits of SMART TV . However, if you have any difficulties with the installation, simply contact our support service for help .
