Do you want to know more about using your set-top box remote control? If so, this guide from ledepotelectronique , titled TVIP Box Remote Control Manual, will provide you with much more information on this topic.
Indeed, as more and more devices are installed in our homes, a device such as a remote control becomes more and more relevant.
In the rest of our article, we will give you more information on using the remote control.
Tvip box remote control manual: how to configure a universal remote control?
To set up a universal remote control, you need to do the following:
Insert the batteries into the remote control
In most cases, universal remotes come with batteries, but you may need to purchase them yourself. The correct battery type should be indicated on the device's packaging.
It's worth remembering right away that many universal remotes "forget" all settings made to them if you remove both batteries. Therefore, replace the batteries one at a time. This will provide the device with enough power so that the universal remote's settings are not erased.
This may also interest you: How to place an order on the electronic deposit?
Turn on the TV
Before setting up the remote control, turn on your TV or any other device you intend to use it for. To do this, use an old remote control or a button on the device body.
Enter the device programming mode: tvip box remote control manual
On the device packaging, in the instructions or, in some cases, on the device case itself, it should be written in detail how to enter the device setup mode. This is usually done by pressing a button or a combination of buttons such as SET and POWER .
Alternatively, some universal remotes are configured from a computer or smartphone using special apps. Others use a TV screen or even a small separate display built into the remote itself.
Assign a device control button
At this point, you need to select the button. And when you press it, the remote will switch to control the device.
For example, if you're thinking about how to set up your remote to control your TV, select the TV button on the remote and press it. Depending on your remote model, you may need to hold the button down longer until the indicator light comes on.
Enter the device code
All supported TVs, DVD players , and other devices are listed in the remote control's instructions with numeric codes. Therefore, in order to configure the universal remote control for a specific device model, you must identify it by entering this code into the remote control's memory.
Typically, to do this, you will enter a few numbers on the remote's keypad and they will be written to its memory. This can be highlighted by the remote's backlight , which will light up in a certain way.
Some universal remotes have a learning mode: they are automatically configured to control the device turned on next to them. If your remote has this mode, see the instructions to activate it. Repeat these five steps for each device and you will be able to control all your devices from a single remote.
You can also find out: How to use timeshift and recording in mytvonline?
TVIP Box Remote Control Manual: How to configure the remote control to operate the VCR?
To configure the remote control to operate the VCR:
1 Turn off your VCR;
2 Press the VCR button on the TV remote control;
3 Press the SET button on the TV remote control;
4 Using the numeric keys on the remote control;
At this point, enter the three-digit code listed for your VCR brand. You must make sure to enter three digits of the code, even if the first digit is "0." (If multiple codes are listed, try the first one.)
5 Press the POWER button on the remote control.
The VCR should turn on if the remote control setting is correct. If the VCR does not turn on, repeat steps 2, 3, and 4, but try one of the other codes for that brand of VCR. If there are no other codes, enter all the VCR codes sequentially from "000" to "080."
In fact, when the remote is in VCR mode , you can still use the volume buttons to adjust the TV volume.
Read also: Mini keyboard to control Smart TVs
TVIP Box Remote Control Manual: How to configure your remote control to operate your cable box?
To configure the remote control to operate your cable box:
1 Turn off your decoder;
2 Press the CABLE button on the TV remote control;
3 Press the SET button on the TV remote control;
4 Using the numeric keys on the remote control;
At this point, enter the three-digit code according to the decoder brand. Make sure you enter three digits of the code, even if the first digit is "0." (If multiple codes are listed, try the first one.)
5 Press the POWER button on the remote control.
If the remote control setting is correct, the cable box should turn on. If the cable box does not turn on after performing this, repeat steps 2, 3, and 4, but also try one of the other codes for the given cable box brand. If there are no other codes, enter all the codes sequentially for a cable TV cable box from "000" to "046."
Conclusion
When streaming TV via the TV BOX, the user uses two remote controls. One is for the decoder and the second remote control is for the TV. The solution to facilitate working with two remote controls is to set up the MAG universal remote control. After configuration, you can use the MAG remote control for additional functions, the main one being: turning the TV on/off.
In addition, to use the remote control more easily without any discomfort, use this article titled: tvip box remote control manual . In addition, you can contact us directly if you need any other information about remote controls that are not mentioned here.
